Danfoss ECtemp 550 Guida di Installazione Pagina 1

MAKING MODERN LIVING POSSIBLEInstallation GuideECtemp 550Electronic Intelligent Thermostatwww.EH.danfoss.com

2. Connect the thermostat according to the connectiondiagram.IP300T30D550Max.Load16 (1) ANTCSensorMains220-240V~NLdevinetNLOADLLOADThe screen of the h

3. Mount and reassemble the thermostat. = Screw holes for mount and reassemble the ther-mostat.▪Fasten the thermostat to a socket or an exterior wallb

3 SettingsThe thermostat is automatically activated when the powersupply is turned on.Note: If the unit has never been activated before, basic con-fig

3.1 Time and Day of Week Settings1. Press and hold the button for 3seconds.The clock symbol appears onthe display and the day of theweek is shown as a

3.2 Basic SettingsThe following table shows the default values of the basicsettings:Item Default setting OptionsNetwork type Alone (ALO) Independent (

How to enter the basic configuration settings1. Press and hold the button for 12 secondsuntil “COdE” appears.2. Turn the button clockwise until “0044”

To define this unit as a slave unit in thenetwork, choose SLA. Only one unit in the network can be defined as masterunit. All slave units will respo

Adaptive regulation: How to specify whether or not tooptimise this thermostat for the room by timing heat-ing start/stop1. Turn the adaptive function

Sensor: How to specify whether an external floor sen-sor, the built-in room sensor or both is used to controlthe floor heating1. Turn the button to ch

How to set the maximum floor temperatureSpecial condition: This setting only applies if a floor sen-sor is used (the FS or rFS sensor option has been

Danfoss A/S is not liable or bound by warranty if theseinstructions are not adhered to during installation or service.The English language is used for

Thermalresist-ance[m2K/W]Examples of floor-ingDetails Approximatesetting for25˚C floortemperature0.05 8 mm HDF basedlaminate> 800 kg/m328˚C0.10 14

Temperature decrease: How to specify how much thetemperature is to be lowered during economy periodsNote: If normal room heating is installed, we reco

ECtemp 55022 Installation Guide

ECtemp 550Danfoss A/SElectric Heating SystemsUlvehavevej 617100 VejleDenmarkPhone:+45 7488 8500Fax: +45 7488 8501Email: [email protected]

ECtemp 550 ELKO088L0044Intelligent TimerThermostatFloor / Room Sensor220-240V~50-60Hz~+5 to +35°C16A/3680@230V~IP 30Product DocumentationDK EL 7224215

Table of Contents1 Introduction ... 31.1 Technical Specifications ... 41.2 Safety Instructions ... 62 Mounting Instructions ...

Note: This thermostat does not apply to tariff control orsimilar systems.More information on this product can also be found at:ectemp.danfoss.com1.1 T

Temperature range +5 to +35°C (room) or +5 to+50 (floor)Lowering in economy peri-ods0 to -30°COffset (temp. correction) -5,5 to +5,5°CCable specificat

1.2 Safety InstructionsMake sure the mains supply to the thermostat is turned offbefore installation. If the thermostat is installed in a net-work, th

2 Mounting InstructionsPlease observe the following placement guidelines:Place the thermostat at a suitable heighton the wall (typically 80-170cm.).Th

Do not place the thermostat in a way thatit will be exposed to direct sunlight.Note: A floor sensor enables a more accu-rate temperature control and i

Follow the steps below to mount the thermostat:1. Open the thermostat:▪Push down the release tab.▪Carefully detach the front cover.▪Remove the two scr